Stop Safely Vehicle Will Shut Off Soon: What to Do?

Imagine you’re driving your Jeep in the city. Suddenly, a warning appeared saying, Stop safely, vehicles will shut off soon. And then the Jeep turns off by itself. It’s really scary and dangerous when a car stops suddenly on the road or at an intersection. This can happen if the main or aux battery is not working well, the alternator is bad, there’s a blown fuse, or the ECM is faulty. Sometimes, just a loose connection can cause this problem.

Lots of you had the same issue, but now there’s no need to worry. I’m going to talk about it in detail here. Just keep reading, it’s important.

What Does The Stop Safely Vehicle Will Shut Off Soon Warning Mean?

When you start your car it usually runs fine for about a minute and then it suddenly says stop safely, vehicle will shut off soon reddit. After that your car starts shaking a lot and eventually stops.  After that, your car starts shaking a lot and eventually stops.

If you see an error while driving and turn off the car’s engine, you might be able to restart it several times without any issues. If you keep the car running, it will eventually shut off.

Here’s what happens: when you start the car, a red battery light comes on, followed by an error message. The message tells you that the start/stop function is not working at the moment.

Sometimes, simply turning the car on and off won’t solve the problem. Even if you replace both batteries, the issue might persist. Your car’s screen could show warnings about the battery, the check engine light, and a very low voltage reading of 10.3 volts.

Reasons Behind Stop Safely Vehicle Will Shut Off Soon Warning & Possible Solutions

There are different reasons why your jeep might show the message to stop safely the vehicle will shut off soon Jeep Wrangler. My Jeep wouldn’t start, but I kept driving like that for a few weeks until I replaced the auxiliary battery. The message went away, and everything seemed fine for a few days. But one day, I forgot to turn off the stop/start feature, and when the Jeep stopped working, I figured out that the main battery was causing the issue.

A person helped me start the jeep, but it caused a lot of problems because it messed up the fuse block near the positive battery connection. I had to replace that fuse block. The main battery still had problems so I put in a new battery and that fixed everything.

There are some different reasons and we explain these reasons one by one:

Read also: Stop/Start Unavailable Service Stop/Start System

Battery

Battery Of Jeeps

Faulty batteries, both the main one and the auxiliary, are the main cause of this problem. When the auxiliary battery is not working properly, it can use up the main battery’s power fast. If you see a red battery icon above a yellow circled “A” on your car’s dashboard, that’s a sign of trouble.

To check, look at the alternator output voltage on the dashboard. It should consistently show 14.4 volts. If it doesn’t, chances are one of the two batteries is probably failing. In that case, it’s a good idea to remove both batteries, test them, and take them to a parts store for further inspection.

Sometimes, when you put in a new battery, you might forget to make sure the power cables are securely attached to the alternator. These cables are usually tightened by hand. If they’re not snug, it could be the reason why your car has trouble starting and stopping properly.

When your car is running, both batteries need to have the same voltage because they are linked directly by a relay. If they’re not connected properly, the extra battery that runs various car functions will slowly lose power and won’t be able to recharge.

Your battery’s power level usually stays between 12.6 and 14.5 volts. The exact number depends on what your battery needs to charge. If you always notice it at 14.4 volts, there could be an issue. Otherwise, it tends to go up and down randomly.

Consider getting the Genesis Gen 3 dual battery kit and install it with two Full Throttle AGM batteries. They all fit under the hood on the same tray. This way, if one of the batteries stops working in the future, you won’t have to search around under the fuse box.

Alternator

One big reason for this issue is the alternator. If you think your battery isn’t charging, you should look into your alternator. Usually, the alternator doesn’t completely stop working, but it might not perform as well.

The alternator is responsible for charging both batteries. The PCM adjusts the charging based on the main battery’s condition

 the throttle, temperature, and a few other things. The auxiliary battery powers all the other devices while the main battery is mainly for starting the car. The Jeep shifts to the main battery to power everything. If the ESS battery runs out or has an issue you’ll see a message saying ESS is not available.

If the stop start system in your car shows it needs maintenance, look into your alternator. See if the voltage regulator is worn out. If it is, you should replace the alternator.

Read also: Can You Tint Jeep Soft Top Windows?

Fuse Box

Fuse Box of Jeep

Individuals facing this issue often neglect to promptly inspect the fuse box but it is strongly recommended that they do so.

At times, the main fuse in the fuse box might need replacing. The start stop relay for the dual battery system could be causing issues. When a mechanic checks for error codes, it may seem like everything is fine, even though dashboard lights and warnings are still on. If you drive with all the equipment, you can capture the issue when it occurs. It might also be a problem with the automatic shutdown relay.

If you suspect the relay is the problem, buy a new one to fix it.

Another issue could be a burnt out fuse. If that’s the case, replace it. We strongly recommend turning off your Jeep’s auto stop before each trip.

When the dealership tested the main and auxiliary batteries and the auxiliary battery failed, they replaced both. The problem persisted. It turned out to be a relay located next to the secondary battery.

Make sure the numbers on the electrical connectors in the fuse box are in the correct order.

Check the large fuse number 5 part of the remote jump post assembly as it guards the connection between the two batteries.

Pay close attention to the high amp fuse array. Many people have a blown N3 fuse in the Fuse Array. If N3 is blown the alternator can’t charge the auxiliary (AUX) battery. This can happen if the disconnected positive cables from the main battery touch nearby metal or N3 in the Fuse Array.

If you put in new batteries, make sure all the fuses in the Fuse Array are working. You can either check each fuse or just get a new Fuse Array. It’s quick to test with a basic multi-meter, about five minutes.

The Fuse Array only costs $50. So, it might be cheaper to just replace it instead of paying a technician by the hour to test it for you.

Pay attention to this. The type of Fuse Array you need for your Jeep relies on whether it has the Tow Package option or not.

If the N3 fuse is blown you can also fix it by shifting the wire from the N3 terminal to the.

Loose Connection

Loose Connection of Jeep

Make sure to look for any wires that aren’t connected well or have rust on them.

When it happened to me the first time, I bought new batteries. Everything was fine for a few weeks but then the alarm came back. I checked the wires and discovered that one of them was too short. After fixing that there were no more alarms.

First, make sure to inspect your car for any loose wires before replacing anything. Pay special attention to the side ground wire if it’s loose, tighten it securely to fix the issue.

You can identify the problem when the voltage of the auxiliary battery drops below 10. To check ,measure the voltage on both batteries. Look under the hood for the positive jump terminal. If it’s loose the auxiliary battery won’t charge.

5. ECM

If the clips are broken be sure to inspect the ECM plug connector on your ECM. If you find any problems there, try adjusting the ECM connectors. If that doesn’t work, you may need to replace them. Once you do this your ECM plug issue should be fixed.

Other Things You Can Do

  • Take out the main and ESS batteries and get their voltage/load checked at auto parts and battery shops.
  • When your jeep  message starts, the Chrysler Pacifica stop safely vehicle will shut off soon and the batteries are fine, check all the fuses under the hood and test the big circuit breakers in the fuse panel.
  • If the stop safely vehicle will shut off soon jeep Compass

message is still there and it’s not the battery or alternator, it could be a problem with the PCM, a corroded connector or sometimes the IBS.

  • The IBS sensor might be giving inconsistent live data or data that was recorded before might be causing issues.
  • If the problem persists and everything else is updated, there might be a powertrain control system update that can fix the reported problem. Check for updates that aren’t OTA yet.

Pros And Cons 

ProsCons
Early Warning SystemAnxiety Inducing – Seeing this message can be stressful,
causing concern about the safety and reliability of the vehicle.
Prevents Further DamageLimited Information – The message may not provide detailed
information about the issue requiring additional diagnostics.
Encourages Immediate ActionPotential for Inconvenience -The vehicle shutting off soon
could lead to inconvenience, especially in inconvenient locations.
Safety Measure for the Vehicle and DriverDependency on Diagnostics – Understanding the root cause
may require professional diagnostics, leading to repair costs.
read also: Uconnect WiFi Hotspot Not Working

Answer The Key Questions

Why does the new Jeep turn off when I stop?

The new Jeep turns off when you stop as part of a feature designed to save fuel. It’s an automatic engine shutoff system that temporarily stops the engine when the vehicle is stationary, reducing fuel consumption

How do you turn off the automatic engine shut off on a Jeep?

To turn off the automatic engine shutoff on a Jeep, refer to your vehicle’s manual. It typically provides instructions on how to disable or adjust this feature according to your preferences.

How do you turn off auto start stop on a Jeep Grand Cherokee 2023?

To disable the auto start stop feature on a Jeep Grand Cherokee 2023, consult the vehicle’s manual. It should contain specific steps or settings to turn off this function, allowing you to control whether the engine stops automatically when the vehicle is stationary.

How does a Jeep auto start and stop work?

Jeep’s auto start stop system is designed to save fuel. It works by automatically turning off the engine when the vehicle comes to a stop, such as at traffic lights. The engine restarts when you press the accelerator, ensuring a seamless transition between being stationary and moving again while optimizing fuel efficiency.

Why does my car turn off as soon as I turn it on?

If your car turns off as soon as you turn it on, it could be due to various issues. Common reasons include problems with the fuel system, a faulty ignition switch, or issues with the electrical system. It’s recommended to have a mechanic check your car to identify and fix the specific issue causing this problem.

Conclusion

The stop safely vehicle will shut off soon is a worrisome issue. Either it will not let you drive at all, or it will stop in dangerous situations. You need to fix it immediately. If you go through the list of reasons above you should be able to pinpoint the problem and solve it.

Before replacing your batteries and spending a lot of money check for a simple issue like blown fuses or wires that aren’t hooked up. Check your alternator relays and ECM. If you don’t use the stop/start system, disable it permanently.

2)The message Your vehicle will shut off soon due to a stop safety problem” is a serious concern. It can either prevent you from driving or cause the car to stop unexpectedly in unsafe situations. It’s crucial to address this issue right away. Review the reasons mentioned earlier to identify the problem and fix it.

Before spending a significant amount on new batteries, first, look for simpler issues like blown fuses or disconnected wires. Examine your alternator relays and ECM. If you don’t use the stop/start system, consider turning it off permanently. This can help you avoid unnecessary expenses and ensure your vehicle operates safely.

Leave a comment